Stain Identification & Tips

Adhesives, including tape residue, cellophane, and stickers, have the potential to leave a persistently sticky residue on the surface of stone. This issue can be particularly challenging when dealing with tape residues, such as those from duct tape, as they may penetrate below the stone's surface, making removal difficult.

To address this problem, the following steps can be taken:

1. Begin by carefully peeling off any remaining tape, utilizing a highly sharp razor blade while exercising caution to avoid scratching the stone's surface or injury.

2. Subsequently, eliminate the residual sticky residue using a clean, white rag and acetone. Apply the acetone to the rag and meticulously rub the affected area until the sticky residue is completely removed.

3. In cases where the adhesive has resulted in a stain, preparing a poultice using a Stone Poultice Powder and mineral spirits is recommended, ensuring adherence to the requisite user and label precautions.

The outlined procedures offer a systematic approach to tackling sticky residue and associated staining issues caused by adhesives on stone surfaces.

When addressing alkaline etching caused by alkaline salts from cleaners, it is advisable to adhere to the following procedures:

1. Endeavor to eliminate the etching using a mild acid, while being mindful not to utilize acid on polished marble.

2. In the case of polished marble, consider the option of re-honing and re-polishing the etch marks.

3. For instances of light etching, it may be appropriate to attempt re-polishing exclusively. 

Aluminum Can leave a crusty, whitish residue.

1. On polished surfaces, scrape any crusty residue from the surface with a sharp razor blade. On textured surfaces, use a stiff brush.

2. On textured surfaces, mix one part hydrochloric acid in 20 parts water, apply the solution, and agitate with a soft nylon brush.

3. On polished surfaces, dilute one part hydrochloric acid in 40 parts water, apply the solution, and agitate with a soft nylon brush. Re-hone and re-polish the surface to return the luster.

Caution: Be extremely careful with hydrochloric acids near marbles; they will severely etch the surface. Please make a note of the following instructions for dealing with 

 When cleaning beer spills on a hard surface, it's essential to follow these steps: 

1. Begin by wiping off the excess beer using a soft cloth or a microfiber cloth to prevent the beer from seeping onto the surface. 

2. Next, thoroughly clean the area using a Surface Buff-approved mild detergent and clean cold water to ensure that the surface is free from any beer residue. 

3. For stubborn stains, you can create a poultice using a mixture of 20-50% hydrogen peroxide and a Surface Buff-approved Stone Poultice Powder.  

Dealing with beer spills on your carpet requires specific steps to ensure thorough cleanup: - For recent spills, immediately remove the beer using clean water and dry cloths or paper towels to prevent the beer from setting into the fabric. - In the case of beer-stained carpet, you can create a gentle cleaning solution using dish soap and vinegar to blot away the stain effectively. - To eliminate lingering beer odors from the carpet, utilize baking soda to absorb the odor-causing particles, and then vacuum the area to remove the smell altogether.

 In addressing non-chocolate candy stains, it is important to start by meticulously scraping off any residual candy from the surface. Following this step, the affected area should be meticulously cleaned using acetone and a clean white cloth. If acetone proves ineffective, the application of Stone Poultice Powder with mineral spirits as a poultice offers an alternative solution to effectively tackle the stubborn stains. 

 All types of coffee, including instant coffee and hot and iced tea, contain tannins, which can cause yellow to brown stains on stone. If left untreated for a long time, the stain can deeply penetrate the stone and become nearly impossible to remove. 

Additionally, if coffee or tea is highly concentrated, it can damage the polished marble's surface.  Here are the steps to remove the stains: 

1. Pour 35% hydrogen peroxide directly on the stain and add a few drops of ammonia. Leave it until the bubbling stops. 

Caution: Do not use ammonia alone; it can permanently set the stain. 

2. If the above procedure does not remove the stain, create a poultice using Stone Poultice Powder and 35% hydrogen peroxide. 

3. If all else fails, use a Surface Buff-approved Stone Poultice Powder with mineral spirits for poulticing.